grid plates
The accurate alignment of workpieces is important for the subsequent manufacturing steps. The SLG grid plate was developed precisely for this purpose. The ground grid plate made of edge-hardened case-hardened steel can be used to set up modular fixtures. Workpieces will be precisely and versatilely clamped, machined and measured on it. This facilitates work, especially with workpieces and parts that have to be extensively clamped or cannot be clamped at all in a vice.
Advantages
- Nitrided and ground
- High basic accuracy of the grid plate: parallelism of 0.015mm
- Low thickness of 35mm.
- Low grid spacing of 40mm (optional 50mm) allows workpieces to be clamped at almost any point on the grid plate.
- The various options allow savings in setup time by requiring workpieces to be set up and calibrated only once.
- Free positioning of the supplied support pins, allowing workpieces to be machined directly on the grid plate without damaging it.
- Configuration according to own requirements possible.
Order your grid plates
- best price
- optionally extendable
- hardened/nitrided
- clamping holes incl.
- protective plugs incl.
Properties of the grid plates
- Nitrided and ground
- Parallelism from 0.015 mm
- Selectable plate length: 200 mm / 400 mm / 600 mm / 800 mm
- Raster holes with selectable thread size M6-M12
- Locking screws for unused holes included
- Grid holes with selectable fitting dimension Ø4F7-Ø12F7
- Support bolts included
- Hole spacing selectable: 40mm or 50mm
- Lateral threaded holes for stops or similar with M8 thread, at 40mm spacing
- Screw-on holes for machine table, T-slot spacings
- Holes for zero point clamping system optionally possible
- Grooves for table alignment optionally possible
- plate without drillings possible as blank
- further options possible on customer request
Characteristics and variants
Item |
R.200.425.35 |
R.400.425.35 |
R.600.425.35 |
R.800.425.35 |
---|---|---|---|---|
Length [mm] |
200 |
400 |
600 |
800 |
Width [mm] |
425 |
425 |
425 |
425 |
Height [mm] |
35 |
35 |
35 |
35 |
Weight [kg] |
22,4 |
44,5 |
66,5 |
88,6 |
Material: |
Case hardening steel 16MnCr5 |
|||
Execution: |
Nitriert und geschliffen |
|||
Parallel: |
0,015 |
0,03 |
0,03 |
0,03 |
Drilling grid |
40x |
90x |
140x |
190x |
Thread dimensions: M6 / M8 / M10 / M12 |
||||
Threaded holes on the side: |
M8, with 40 mm spacing |
|||
Raster holes fitting holes [mm]: |
27x |
72x |
117x |
162x |
Dimensions: Ø4F7 / Ø6F7 / Ø8F7 / Ø12F7 |
||||
Stud bolts DIN 913 PA: |
40x contain |
90x contain |
140x contain |
190x contain |
Support bolt DIN 6321: |
27x contain |
72x contain |
117x contain |
162x contain |
Table slot drillings nach DIN 55200 [mm]: |
Dimensions: 125 / 100 / 63 |
|||
Holes for zero point clamping system: |
Optionally, |
Optionally, |
Optionally, |
Optionally, |
Grooves for table alignment: |
Optionally, |
Optionally, |
Optionally, |
Optionally, |